![]() Unlike Final Cut Express and Final Cut Pro, iMovie won't allow you to directly import the. ![]() It will mount and iMovie will behave as if you've plugged in your camcorder. When you'd like access to the camcorder's media (as saved when you created the disk image file), launch iMovie and double-click on the disk image file. Once it finishes, you can unmount the camcorder's drive and disconnect the camera. In the resulting sheet choose Read/Write from the Image Format pop-up menu, None from the Encryption pop-up menu, and click the Save button.ĭisk Utility will set about creating a disk image file of the camcorder's media drive. You can also create a duplicate copy of that camcorder's hard drive by launching Disk Utility (found in /Applications/Utilities), selecting it in the list of drives and volumes on the left side of the Disk Utility window, and choosing File -> New -> Disk Image From disknumber (where disknumber is the name give to the selected disk). The most obvious option is to simply import everything on the camcorder's hard drive into iMovie. I was wondering if there was a way for me to make a copy of its hard drive that I could use with iMovie. Better yet, post a small sample m2t file here and let me see if anyone here on the board can transcode them (I'll bet someone can figure out a workflow.I have a Sony AVCHD camcorder that I don't always keep at home. Call DataVideo and see if they have any suggestions. If you have Windows on your machine try the windows app I mentioned above. Use MPEGStreamclip to Transcode a file to ProRes. ![]() Try to transcode the ProRes files that are crashing FCP X, to another ProRes format in Compressor, that might clean up the files. Don't worry however, we will figure out a solution So your basically at the same place you were when you started. However, I found on this site, that there is definitely some possible issues with these files. m2t files to use with Final Cut Pro?Ī: You can use a program like, Streamclip to convert the. Q: Final Cut Pro does not natively support the. I found the software here but it is Windows only: HDV and MXF-OP1A through MAC or PC software conversion program I noticed on the spec sheet for that your recorder that it says:įile support includes: AVI, MOV, MXF-OP1A, M2T format, QuickTime But there can be issues with it's M2T format as I did a little research: It looks like the Datavideo DN-60 external recorder is a pretty neat little device. When I import the file to FCPX it crashes again.Īgghhh! This is just HDV! Please someone tell me I don't have to start editing this project in my antiquated PC with Adobe CS3 (that handled all of this stuff years ago without any issues)! ![]() Quicktime fails to open this movie, and I have to force quit. There are a number of options to transcode the footage directly in Clipwrap to ProRes 422 etc (not just wrapping the clips) - so I try 422HQ which it does no problem. This goes on for a while before FCPX gives me an option to open without the previous open windows, allowing me to trash the project and prevent further crashes. Subsequent attempts to open FCPX gets me into a cycle where it tries to transcode again, and crashes again. So I try to import the footage with transcoding, and FCPX locks up and crashes. Then I imported the clips into FCPX (without transcoding) to confirm all is well before I purchase the software.and the footage is intermittently blocky and corrupted. The conversions from M2T to MOV are very quick, and the resultant clips played well in Quicktime. I tried the Clipwrap demo (which works the same as the full version but limited to 1 minute clips). Does anyone have experience of this program and would this be the best way forward? Anyone know for sure if the program is compatible with Lion and FCP X? Any other options out there? Does that sound right (that FCP X would not be able to transcode the files)?Ī little bit of research on the internet led me to a program called Clipwrap which wraps the M2T files into MOV files which should work. I kind of thought I would be able to transcode them at the point of import into FCP X, but seemingly this is not possible. I cant import the files into FCP X as they are greyed out. When I view the files in the finder it calls them “Unix Executable File” and shows an image with a lock over them. M2T files worked fine with Adobe CS3 on a PC, but the Mac does not seem to recognize the files at all. However I ran into a hurdle at the fist step.īasically I am trying to import HDV footage that was filmed over a year a go, and captured to a Datavideo DN-60 external recorder. I purchased the Ripple Training tutorials and finished the included projects without any problems (no crashes or bugs to speak of) so I felt I was ready to start editing my first project in FCP X. I’m new to apple computers and new to FCP so bear with me as I am still learning how to do things with this OS and with FCP X.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |